Go Back   ATVConnection.com ATV Enthusiast Community » Brand Discussions Area » Yamaha
Sign in using an external account
Register Forgot Password?
Register ATV Photos FAQ Members Calendar Search Today's Posts Mark Forums Read GarageVendors
Search
Welcome to ATVConnection.com ATV Enthusiast Community

Reply Share this with your friends
  #1 (permalink)  
Old 01-25-2005, 10:55 PM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2005
Posts: 330
Send a message via AIM to NastyNate03
Default installing trinity stage IV intake/carb on 03 banshee some questions

i just got a trinity stage IV single 35mm carb and intake for my 03 banshee its all stock its the first mod i took out the stock carbs to install the new carb when i took out the stock carbs i had to unplug the electrical wires 2 of them that connect to the carbs what do i do with these wires
Reply With Quote
  #2 (permalink)  
Old 01-26-2005, 11:48 AM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2001
Posts: 1,850
Default installing trinity stage IV intake/carb on 03 banshee some questions

Leave the wires hanging or tie them up. You won't use them anymore. Now, under the gas tank on the front drivers side there is a little black box that has a wire coming out of it that goes to a white triangle plug. Unplug that plug and you can remove the black box if you want. If you don't unplug it, your engine will not rev up.
Reply With Quote
  #3 (permalink)  
Old 01-26-2005, 02:37 PM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2005
Posts: 330
Send a message via AIM to NastyNate03
Default installing trinity stage IV intake/carb on 03 banshee some questions

im just about done the install theres 2 boxes side by side are you talking about the black box that is only about the size of a 9v battery is smaller then the other one has 3 wires coming out of it black, black/white, and yellow/black wires and its on the side closer to the kill switch and lights switch and should i trace and take out all the wires that are disconnected now or just tape them off so no mud water gets in them
Reply With Quote
  #4 (permalink)  
Old 01-26-2005, 10:04 PM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2005
Posts: 330
Send a message via AIM to NastyNate03
Default installing trinity stage IV intake/carb on 03 banshee some questions

anyone?
Reply With Quote
  #5 (permalink)  
Old 01-26-2005, 11:06 PM
Pro Rider
Garage is empty, add now
 
Join Date: Dec 2002
Posts: 1,771
Default installing trinity stage IV intake/carb on 03 banshee some questions

Cut the two plugs off the Tors. Then each plug has two wire, connect them together. Now plug them in the original connectors in the harness.[img]i/expressions/face-icon-small-wink.gif[/img]
Reply With Quote
  #6 (permalink)  
Old 01-26-2005, 11:13 PM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2005
Posts: 330
Send a message via AIM to NastyNate03
Default installing trinity stage IV intake/carb on 03 banshee some questions

so i cut the 2 plugs off the wires that were connected to the carbs? do i twist the 2 wires together on each plug or twist all 4 together then what harness do i plug them in also am i talking about the right box to disconnect
Reply With Quote
  #7 (permalink)  
Old 01-27-2005, 12:24 AM
Pro Rider
Garage is empty, add now
 
Join Date: Dec 2002
Posts: 1,771
Default installing trinity stage IV intake/carb on 03 banshee some questions

No just the two wires per plug you tie together. Then you plug them back where you disconnected them from on the harness.

As far as the black box it should be the smaller one with two wires going to it I think!!!
Reply With Quote
  #8 (permalink)  
Old 01-27-2005, 12:33 AM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2005
Posts: 330
Send a message via AIM to NastyNate03
Default installing trinity stage IV intake/carb on 03 banshee some questions

i dont get what your saying on the harness that runs along the whole frame theres 2 plugs coming out of it 2 wires on each plug each plug connected into the stock carbs so where on the harness am i supposed to put them and the smaller box has 3 wires coming out of it not 2
Reply With Quote
  #9 (permalink)  
Old 01-27-2005, 11:20 AM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2001
Posts: 1,850
Default installing trinity stage IV intake/carb on 03 banshee some questions

Ernie has you all screwed up. Simply do what I said and unplug the triangular plug. It comes from that little black box that you say that is the size of a 9 volt. You don't have to tape up or splice anything just unplug it.
Reply With Quote
  #10 (permalink)  
Old 01-27-2005, 12:43 PM
Pro Rider
Garage is empty, add now
 
Join Date: Jan 2005
Posts: 330
Send a message via AIM to NastyNate03
Default installing trinity stage IV intake/carb on 03 banshee some questions

ok ill do that what is that box called also is it worth tracing all the plugs and taking them out of the harness also what is the best air intake setup to get to get the most air to the filter right now i have a k&n filter with pro flow adapter plate and the stock air intake box with a hole cut in it
Reply With Quote
Old 01-27-2005, 12:43 PM
Reply Share this with your friends

Tags
2001, banshee, black, box, carb, carbs, installing, intake, iv, parts, performance, single, stage, trinity, tune



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On