Need a little help with LTZ 400 carb setup
#1
Need a little help with LTZ 400 carb setup
I just picked up a 2004 Z400 for my fiance the other day and need a little help here. Supposedly it has a HotRods stage 2 cam, does have full exhaust and it has a large (not sure size) Keihin FCR carb on it. The carb does not have a choke so it won't start when cold and then it also sputters when first hitting the throttle. Once going 4-5 mph its ok, just falls on its face off the bat. Any ideas? Also looking for an original carb, if I go that route any ideas what the jetting should be? Any help would be greatly appreciated.
BTW, I'm new here with this as a first post but looks to be alot of knowledge around this place! I'm sure I'll need it as I'm used to the 2 smoker bikes!
BTW, I'm new here with this as a first post but looks to be alot of knowledge around this place! I'm sure I'll need it as I'm used to the 2 smoker bikes!
#4
#5
"you should get rid of that carb,good carb,but not for what you have.use stock carb and proper jetting you'll have no problems,ive dyno'd many of these with factory carb, excellent results."hahahaha dont know what dyno your using!
ummmm the kehin FCR carbs (39,40,41 etc) outperform the stock 36mm Mikuni CV carb in every way! Especially on the z400. that has to be one of the most common and best mod you can do to the motor.its is fairly easy to fix the problems you have described. the "sputtering" that happens at low engine speeds is the infamous "bog". there are a few ways to fix it.
1. The O-ring mod
2. get a Quickshot for it
3. Tune the accelerator pump timing....etc
Everybody that i've heard of thats switched to the FCR would never go back to the junk stock carb. and there should be a pull out choke mounted on the left side of the carb towards the top.
BTW,HotRods doesnt make cams, Hotcams does. there are two cams in the Z motor. do you know if both or just one is aftermarket? good luck!
ummmm the kehin FCR carbs (39,40,41 etc) outperform the stock 36mm Mikuni CV carb in every way! Especially on the z400. that has to be one of the most common and best mod you can do to the motor.its is fairly easy to fix the problems you have described. the "sputtering" that happens at low engine speeds is the infamous "bog". there are a few ways to fix it.
1. The O-ring mod
2. get a Quickshot for it
3. Tune the accelerator pump timing....etc
Everybody that i've heard of thats switched to the FCR would never go back to the junk stock carb. and there should be a pull out choke mounted on the left side of the carb towards the top.
BTW,HotRods doesnt make cams, Hotcams does. there are two cams in the Z motor. do you know if both or just one is aftermarket? good luck!
#6
Thanks for the advice! Any chance you could explain to me how to do the O-ring mod, tune the accelerator pump timing and explain what a quick shot is? Sorry, may be stupid questions but I'm new to quads as far an working on htem go for the most part. My email is bhensley1980@sbcglobal.net if you would prefer that. Thanks alot. Also, any way you could explain in better detail where the choke "should be" so I can figure out how to fix it? Once again, thanks for the help and advise!
"you should get rid of that carb,good carb,but not for what you have.use stock carb and proper jetting you'll have no problems,ive dyno'd many of these with factory carb, excellent results."hahahaha dont know what dyno your using!
ummmm the kehin FCR carbs (39,40,41 etc) outperform the stock 36mm Mikuni CV carb in every way! Especially on the z400. that has to be one of the most common and best mod you can do to the motor.its is fairly easy to fix the problems you have described. the "sputtering" that happens at low engine speeds is the infamous "bog". there are a few ways to fix it.
1. The O-ring mod
2. get a Quickshot for it
3. Tune the accelerator pump timing....etc
Everybody that i've heard of thats switched to the FCR would never go back to the junk stock carb. and there should be a pull out choke mounted on the left side of the carb towards the top.
BTW,HotRods doesnt make cams, Hotcams does. there are two cams in the Z motor. do you know if both or just one is aftermarket? good luck!
ummmm the kehin FCR carbs (39,40,41 etc) outperform the stock 36mm Mikuni CV carb in every way! Especially on the z400. that has to be one of the most common and best mod you can do to the motor.its is fairly easy to fix the problems you have described. the "sputtering" that happens at low engine speeds is the infamous "bog". there are a few ways to fix it.
1. The O-ring mod
2. get a Quickshot for it
3. Tune the accelerator pump timing....etc
Everybody that i've heard of thats switched to the FCR would never go back to the junk stock carb. and there should be a pull out choke mounted on the left side of the carb towards the top.
BTW,HotRods doesnt make cams, Hotcams does. there are two cams in the Z motor. do you know if both or just one is aftermarket? good luck!
#7
Trending Topics
#8
i was trying to imply a cheaper easier method for him not all off us can be as perfect as you,ive used both of the above,for some one who wants no problems or an easy fix the stocker is the way to go,he never asked about out performing the stock carb.some things you shouldnt mess with if you dont know what your doing,at least someone knows how to use a dyno,and can give advise without suggesting they spend more money!anytime u think you have somthing that performs well come to california,dumont dunes,banshee hill,i can teach u how to go fast,and not just with your mouth.ghive a guy a used quad and all of a sudden he's a pro!
#10